Parameterization¶
The arrangement of the parameter data is depending on the firmware version installed inside the CPUs and Bus Modules:
| Firmware version | Mounting position | Configuration |
|---|---|---|
| Firmware version < V2.0.0 |
|
The arrangement of the parameter data is performed by PLC-Configuration inside Control Builder software. |
|
The arrangement of the parameter data is performed by your master configuration software SYCON.net in connection with the S500 GSD files and in conjunction with the Control Builder software. | |
| Firmware version > V2.0.0 |
|
The arrangement of the parameter data is performed by Control Builder Plus software. |
The parameter data directly influences the functionality of modules.
For non-standard applications, it is necessary to adapt the parameters to your system configuration.
| Name | Value | Internal Value | Internal value, Type | Default | Min. | Max. | EDS Slot Index |
| Module ID | Intern | 1805 *1) | WORD | 0x070D | 0 | 65535 | 0x0Y01 |
| Ignore module *2) | No Yes |
0 1 |
BYTE | No 0x00 |
Not for FBP | ||
| Parameter length | Internal | 6 | BYTE | 0 | 0 | 255 | xx02 *3) |
| Check supply | Off On |
0 1 |
BYTE | On 0x01 |
0x0Y03 | ||
| Input delay | 0.1 ms 1 ms 8 ms 32 ms |
0 1 2 3 |
BYTE | 8 ms 0x02 |
0 | 3 | 0x0Y04 |
| Mode Counter 0 | see table below | 0 | BYTE | 0x00 | 0 | 15 | 0x0Y05 |
| Counter 0 frequency limit | No filter 50 Hz 500 Hz 5 kHz 20 kHz |
0 1 2 3 4 |
BYTE | No filter 0x00 |
0 | 4 | 0x0Y06 |
| Counter 0 input level | 0-24 V DC 0-5 V DC Differential 1 Vpp sinus |
0 1 2 3 |
BYTE | 0-24 V DC 0x00 | 0 | 3 | 0X0Y07 |
| SSI 0 frequency | 200 kHz 500 kHz 1 MHz |
2 3 4 |
BYTE | 200 kHz 0x02 |
0 | 4 | 0x0Y08 |
| SSI 0 resolution (in bit) | 8 to 32 bit | BYTE | 16 bit 16 |
8 | 32 | 0x0Y09 | |
| SSI 0 code type | Binary | 0 | BYTE | Binary 0 |
0 | 0 | 0x0Y0A |
| SSI 0 polling time | 10 ms | BYTE | 10 | 1 | 255 | 0x0Y0B | |
| 5 V sensor 0 supply | Off On |
0 | BYTE | Off 0x00 |
0 | 1 | 0x0Y0C |
| Mode Counter 1 | see table below | 0 | BYTE | 0x00 | 0 | 15 | 0x0Y0D |
| Counter 1 frequency limit | No filter 50 Hz 500 Hz 5 kHz 20 kHz |
0 1 2 3 4 |
BYTE | No filter 0x00 |
0 | 4 | 0x0Y0E |
| Counter 1 input level | 0-24 V DC 0-5 V DC Differential 1 Vpp sinus |
0 1 2 3 |
BYTE | 0-24 V DC 0x00 | 0 | 3 | 0X0Y0F |
| SSI 1 frequency | 200 kHz 500 kHz 1 MHz |
2 3 4 |
BYTE | 200 kHz 0x02 |
2 | 4 | 0x0Y10 |
| SSI 1 resolution (in bit) | 8 to 32 bit | BYTE | 16 bit 16 |
8 | 32 | 0x0Y11 | |
| SSI 1 code type | Binary | 0 | BYTE | Binary 0 |
0 | 0 | 0x0Y12 |
| SSI 1 polling time | 10 ms | BYTE | 10 | 1 | 255 | 0x0Y13 | |
| 5 V sensor 1 supply | Off On |
0 | BYTE | Off 0x00 |
0 | 1 | 0x0Y14 |
| Detection SC on sensors | Off On |
0 | BYTE | Off 0x00 |
0 | 1 | 0x0Y15 |
| Output behaviour com fault | Off Last value Substitute Last value 5s Substitute 5s Last value 10s Substitute 10s |
0 1 2 3 4 5 6 |
BYTE | Off 0x00 |
0 | 1 | 0x0Y16 |
| Substitute value | 0 | 0 | WORD | Default 0x0000 |
0 | 65536 | 0x0Y17 |
*1) with CS31 and addresses less than 70 and FBP, the value is increased by 1
*2) Not with FBP
*3) Value is hexadecimal: HighByte is slot (xx: 0 … 7), LowByte is index (1 … n)
Operating modes for counters 0 and 1, configuration table:
| Internal value | Operating modes of counter |
|---|---|
| 0 | No counter / No PWM (default value) |
| 1 | 1-1 UpDown counter (A) |
| 2 | 2-1 UpDown with release input |
| 3 | 3-2 UpDown counters (A, B) |
| 4 | 4-2 UpDown (A, B on falling edges) |
| 5 | 5-1 UpDown dynamic set (B) / rising edge |
| 6 | 6-1 UpDown dynamic set (B) / falling edge |
| 7 | Not used |
| 8 | 8-1 UpDown with release (B), 0 cross detection |
| 9 - 19 | Not used |
| 20 | 11-1 Incremental encoder |
| 21 | 12-2 Incremental encoder X2 |
| 22 | 13-1 Incremental encoder X4 |
| 30 | 14-1 SSI, absolute encoder |
| 40 | 15-1 Time frequency meter |
| GSD file: | Ext_User_Prm_Data_Len = Ext_User_Prm_Data_Const(0) = |
25 0x07, 0x0E, 0x17, \ 0x01, 0x02, \ 0x00, 0x00, 0x00, 0x02, 0x10, 0x00, 0x0A, 0x00, \ 0x00, 0x00, 0x00, 0x02, 0x10, 0x00, 0x0A, 0x00, \ 0x00, 0x00, 0x00, 0x00; |